Resolving double NAT issues
This article outlines how to troubleshoot various problems that may occur with your Sonos system potentially caused by a network setup known as “Double NAT”.
What is double NAT?
NAT, or “Network Address Translation”, refers to a protocol used by routers to let multiple devices (such as your Sonos products) on a private local network (your personal WiFi) share a single public IP address when connecting to the internet.
“Double NAT” is what happens when your internet is performing this protocol twice, typically due to having a minimum of two networking hardware devices (such as an ISP supplied modem/router, as well as any separately-purchased second router or mesh system). In this setup, both the first router and the second router are both maintaining their own individual lists of your at-home wireless devices and Sonos products, and providing their own public IP addresses.
Symptoms of double NAT
- Unable to connect to the Sonos app, and instead seeing an error message that says “System not found”.
- Different mobile devices, such as a phone or tablet, may show as connected to different Sonos products. This is a sign that each mobile device might actually be connected to a different WiFi network.
- Sonos products often alternate between showing as online and offline, especially right after a power outage or router reboot.
- Issues seem to have begun only after making a change to your home network. This can include installing a new router, mesh kit, or having networking equipment replaced by your Internet Service Provider (ISP).
Why does it cause issues with Sonos?
Sonos products don’t route through the internet to find each other or your phone. Instead, they find each other by broadcasting on the local network, using standard discovery protocols (UPnP / SSDP).
This broadcasting only works when the app and every Sonos product are all using the same WiFi network. A second router may create a second WiFi network, whether or not it’s specifically performing Network Address Translation (NAT). Without additional network configuration, once two routers are both active, the house effectively has two separate WiFi networks stitched together, with the routers built to prevent devices connected to its network from being seen by other networks.
In other words, devices connected to the first router may not see devices connected to the second router, even if the two routers are wired together.
This is also why the same symptoms may appear in other setups that aren't technically "double NAT", which can include network setups such as a guest WiFi network, or a WiFi extender creating its own network. The underlying problem is identical; your mobile device and your Sonos products aren't connected to the same network.
Supported network setups
The table below shows the same home with two routers. The scenario on the left shows the two routers as active, without additional network configuration. The scenario on the right shows the same routers, but one of them has had their settings configured properly. The only difference between them is that one setup actively determines which networking device is broadcasting WiFi.
Unsupported - Two routers, both active
Supported - One router set to bridge mode
- First router broadcasting “HomeWiFi” network
- Second router broadcasting a different network, named “HomeWireless”
- The phone connects to the first router’s WiFi.
- Sonos products connect to the second router’s WiFi.
- First router set to bridge mode - causing it to act as modem only, with both WiFi and NAT (Network Address Translation) turned off.
- The second router is now the only router broadcasting a single network, titled “HomeWireless”.
- The phone connects to “HomeWireless”.
- Sonos products also connect to “HomeWireless”.
Product discovery blocked: mobile device and Sonos connected to two separate networks.
Product discovery success: mobile device and Sonos products connected using one network.
Resolving double NAT
Put one router in bridge mode (preferred)
Bridge mode turns a router/modem into a plain modem and disables NAT (Network Address Translation), DHCP (Dynamic Host Configuration Protocol), and WiFi broadcasting. This allows your other router to become the only one performing NAT or broadcasting WiFi.
Refer to your ISP for steps on how to enable Bridge mode if using their specific provided router or modem.
Use only one router
Customers often find they do not need a second router in their home. In this case, remove the old router by disconnecting it from power and leaving it powered off.
For this fix, check the section below to ensure the unused WiFi network name has also been removed from Sonos.
Rename WiFi network names
If placing one router into Bridge mode is not an option, consider renaming the two WiFi networks to have unique names.
As an example, you may select names like “HomeWiFi” for one network, and “WorkWiFi” for the second network.
Once your WiFi networks are uniquely named, connect your phone and your Sonos products to only the chosen WiFi network. This makes it easier to verify the Sonos and your phone are connecting to the same router.
For this fix, you must remove the old WiFi network name from Sonos.
Wired Sonos systems
If encountering a double NAT scenario on a Sonos system that is operating in a wired setup, ensure that any Sonos products wired to your network are wired to the chosen router.
Do not wire any Sonos products to a router or modem that has been placed in Bridge Mode.